ASL INTERCOM PS 4379 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Interphones de porte ASL INTERCOM PS 4379. ASL PS 6379 - ASL-USA Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 4
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
ASL PS 6379
This description also applies to the the PS-4379. It has four channels instead
of six and 1 amp less current rating.
The PS 6379 is a 6-Channel Master Station with built in power supply and is
compatible with all other ASL PRO – and BASIC Series Products as well as
other industry standard unbalanced two-wire party line systems..
Front panel
Speaker on/off
The Speaker of the PS 6379 is switched on and off by the Speaker on/off button. Thv e speaker LED
indicates the speaker status.
Stage Announce
By pushing and holding the stage announce button the microphone signal is directed to the stage
announce connector at the back of the unit. The microphone signal will no longer go to any Intercom
channel even when the TALK LED is switched on.
The signal will also be send to the D9 connector at the back of the unit, which contains a relay contact
(DPST). This signal can be used to switch, for example, a light or an amplifier.
CALL
A combined visual and audio call system covers light and/or sound sensitive environments. CALL
buttons enable the user to generate a call signal to each channel separately and is indicated by a large
LED. If a CALL button is held for more then 2 seconds, the internal audio buzzer is activated . The
volume of the buzzer can be trimmed or muted.
When the channel is in IFB mode the call button is disabled.
ALL CALL
By pushing and holding the CALL to ALL button a call signal is send to all channels which are not in
IFB mode.
TALK
The TALK buttons are latching or momentary and allow the user to talk to one channel only or to a
number of channels simultaneously. The microphone signal is sent to the channels on which the TALK
LED is lit.
A single tap of the TALK button will latch it in TALK mode. Pushing and holding the TALK button for
more than 2 seconds makes it momentary. The TALK function and LED will switch off upon release of
the TALK button.
For each channel the latching mode of the TALK button can be switched off by an internal dip switch.
When the channel is in IFB mode the talk button is always momentary.
ALL TALK
By pushing and holding the ‘TALK to ALL’ button the microphone signal is sent to all channels which
are not in IFB mode. When the ‘IFB-in-talk-all’ dip switch is on, the signal is also sent to the channels
which are in IFB mode.
MIC MUTE
By pushing the ‘MIC MUTE’ button the power-supply of the corresponding channel is interrupted for
approximately 100 ms. This makes all units on the corresponding channel to switch off the
microphones.
Vue de la page 0
1 2 3 4

Résumé du contenu

Page 1 - ASL PS 6379

ASL PS 6379 This description also applies to the the PS-4379. It has four channels instead of six and 1 amp less current rating. The PS 6379 is

Page 2 - Gooseneck Microphone

The mic mute LED indicates that the ‘MIC MUTE’ button was activated and stays on for one more second after the ‘MIC MUTE’ button has been released. A

Page 3 - Headset Connector

gooseneck microphone is disabled. When the unit is connected to an other unit using a link cable and this unit is the slave the gooseneck microphone i

Page 4 - Inside the unit

SLAVE MODE When connecting a channel of a PS 6379 or PS 4379 to a system which already supplies power, this channel of the PS 6379 or PS 4379 will go

Commentaires sur ces manuels

Pas de commentaire